太阳3娱乐|太阳3平台

安装说明VIEWS

太阳3娱乐|太阳3平台

ZTF型可调阻尼弹簧减震器安装说明

来源:ZTF型可调阻尼弹簧减震器安装说明 宣布于:2018-11-14 12:06   浏览:
ZTF型可调阻尼弹簧减震器安裝說明 
ZTF spring isolator installation guide
 
安裝前,请确认弹簧减震器的型号规格是否正确。
Before installation, make sure the model and the specification are correct.
安装说明
Installation guide
所需工具:公制口径19mm (M12)、24mm (M16)、32mm (M22) 开口扳手、爪式千斤.。
Required tools: 19mm (M12), 24mm (M16) and 32mm (M22) open wrenches and claw jack.
在未完成减震器高度调整前,请勿将减震器的压垫取出。
Before completing the adjustment of the isolator, do not remove the pressure pad from the isolator.
请先凭据基础螺栓牢固孔的位置,与安裝位置预埋基础螺栓。
Embed foundation bolt according to the location of bolt-loaded holes.
弹簧减震器安放到安裝位置后,先將定位柳钉拿掉。( 如图1 )
Remove quilting rivet after installing the isolator (Fig 1) .
以M12牢固螺栓将减震器与设备牢固,但不锁紧。( 如图2 )
Fasten the isolator and the equipment with M12 fixed bolt without locking it (Fig 2).
将减震器利用基础螺栓牢固到地面上,並以临时木台牢固高度。
Fasten the isolator with foundation bolt on the ground and fix the height with wooden panel.



 
规格
外形尺寸(mm)
牢固
螺栓
ØBD
L
W
L1
W1
A
B
H
ZTF-1
260
100
210
100
230
0
200
12
13
ZTF-2
235
220
235
140
195
180
200
14
13
ZTF-4
320
165
320
165
290
90
200
14
13
ZTF-6
400
170
400
170
370
90
200
18
13
ZTF-9
420
250
420
250
384
180
200
18
13
 
*B值为0表孔中心在W/2
挠度可定制40mm、50mm、75mm、100mm、125mm、150mm                                              
 
型号/规格
载荷规模(kg)
竖向刚度(kg/mm)
适用挠度(mm)
ZTF-1-100
80~120
4
25
ZTF-1-150
120~180
6
25
ZTF-1-200
160~240
8
25
ZTF-1-250
200~300
10
25
ZTF-1-300
240~360
12
25
ZTF-1-350
280~420
14
25
ZTF-1-400
320~480
16
25
ZTF-1-450
360~540
18
25
ZTF-1-500
400~600
20
25
ZTF-1-600
480~720
24
25
ZTF-1-700
560~840
28
25
ZTF-1-850
680~1020
34
25
ZTF-1-1000
800~1200
40
25
ZTF-1-1200
960~1440
48
25
ZTF-2-600
480~720
24
25
ZTF-2-800
640~960
32
25
ZTF-2-900
720~1080
36
25
ZTF-2-1000
800~1200
40
25
ZTF-2-1200
920~1440
48
25
ZTF-2-1400
1120~1680
56
25
ZTF-2-1600
1280~1920
64
25
ZTF-2-2000
1600~2400
80
25
ZTF-4-600
480~720
24
25
ZTF-4-800
640~960
32
25
ZTF-4-1000
800~1200
40
25
ZTF-4-1200
960~1440
48
25
ZTF-4-1400
1120~1680
56
25
ZTF-4-1600
1280~1920
64
25
ZTF-4-2000
1600~2400
80
25
ZTF-4-2400
1920~2880
96
25
ZTF-4-2800
2240~3360
112
25
ZTF-4-3200
2560~3840
128
25
ZTF-4-4000
3200~4800
160
25
ZTF-4-4800
3840~5760
192
25
ZTF-6-3600
2880~4320
144
25
ZTF-6-4200
3360~5040
168
25
ZTF-6-5000
4000~6000
200
25
ZTF-6-6000
4800~7200
240
25
ZTF-6-7200
5760~8640
288
25
ZTF-9-4500
3600~5400
180
25      
 
 
 
 
ZTF-9-5400
4320~6480
216
25       
ZTF-9-6300
5040~7560
252
25
ZTF-9-7200
5760~8640
288
25
ZTF-9-9000
7200~10800
360
25
ZTF-9-10800
8640~12960
432
25


调整弹簧减震器高度时先松掉两边的反掣螺帽5~10mm ,並相对锁紧。( 如图3 )
Loosen the nuts on both sides for 5~10mm first before adjusting height of the isolator and lock them afterwards (Fig 3).
使用公制口径32mm 开口扳手以逆时针偏向调整M22螺栓,使弹簧受力下压、弹簧减震器上盖铁上升。(如图4 )
Adjust M22 adjustment bolt in the anti-clockwise direction with 32mm open wrench to press down the spring and to raise the iron sheet (Fig 4).
调整*压垫可取出时,即可停止调整并取出木台。( 如图5 )
Adjustment can be stopped and wooden panel can be removed once you can take out the pressure pad (Fig 5).
将与设备牢固之M12螺栓完全锁紧,即完成安装调整。( 如图6 )
After the adjustment, lock the isolator with M12 fixed bolt (Fig 6).
安装后请检查弹簧之下压量,如弹簧压实体现荷重不足没有避震效果。应予更换较大荷重之规格,并请联系本公司人员。
After the adjustment, check the press amount of the spring. If it appears with insufficient loading,pleaereplace with bigger loading by contacting our staff.
安装时,请注意宁静。
Be cautious during the installation.
 
调养点检项目:每月视察牢固螺栓与基础螺栓保持锁紧、保持避震器安装状态&弹簧下压挠度正常。
Maintenance checking points: Check the mounting bolts, remain fixed bolt locked, installation of the isolator, and the deflection of the spring.

图1) 将定位柳丁取出,並以木台牢固高度。
Fig 1) Remove quilting rivet and fix the height with wooden panel.
ZTF型可调阻尼弹簧减震器安装说明

图2) 以M12螺栓将弹簧减震器与设备牢固,但不锁紧;同时以基础螺栓将弹簧减震器牢固。
Fig 2) Fasten the isolator and the Equipment with M12 fixed bolt without locking it. Fasten the isolator with foundation bolt.
ZTF型可调阻尼弹簧减震器安装说明

图3) 调整弹簧减震器太过时,先松掉两边之反掣螺帽5~10mm ,并相对锁紧。
Fig 3) Loosen the nuts on both sides for 5~10mm first before adjusting height of the isolator and lock them afterwards.
ZTF型可调阻尼弹簧减震器安装说明

图4) 使用公制开口板手以逆时针偏向调整螺栓,使弹簧下压、弹簧减震器上盖铁上升。
Fig 4) Adjust the bolt in the anticlockwise direction with open wrench to press down the spring and to raise the iron sheet.
ZTF型可调阻尼弹簧减震器安装说明

图5) 调整*弹簧减震器上盖铁升高,压垫可以取出时即可完成调整并取出木台。
Fig 5) Adjust until the iron sheet of the isolator arises. Adjustment can be stopped and wooden panel can be removed once you can take out the pressure pad.
ZTF型可调阻尼弹簧减震器安装说明

图6) 将螺栓与设备完全锁紧后,即完成弹簧减震器安裝调整。
Fig 6) After the adjustment, lock the isolator with M12 fixed bolt 5-10mm
ZTF型可调阻尼弹簧减震器安装说明

点击下载:




  • 上一篇:JB型可调阻尼弹簧减震器安装说明

  • 下一篇:ZTA阻尼弹簧减震器安装说明




  • 最新推荐: